Nondestructive Characterization of Materials II

I - Polymers and Composites.- Process Controls and Nondestructive Evaluation of Structural Composites. (Invited).- In-Process Ultrasonic Nondestructive Evaluation.- Nondestructive Characterization of Kevlar Composites Using Pulsed NMR.- Cure Monitoring of Composite Structure Using Mechanical Impedance Analysis (MIA).- Ultrasonic Characterization of Polymers in their Evolution from Solid to Liquid State.- Polar Characteristics of the Group and Phase Velocities of Lamb Waves in Graphite/Epoxy Composite.- Development of a Comprehensive Approach for Acoustic Emission Monitoring of Carbon-Epoxy Composites.- Application of the Ultrasonic Approach to the Characterization of Composites: A Method for the Determination of Density in Polyethylene.- NDE Composite Laminates by Leaky Lamb Waves and a Bubbler.- Characterization of Isotropic Composites Containing Inclusions of Specified Shapes by use of Ultrasonics in the Long Wavelength Limit.- Characterization of Composite and Adhesive Cure by Ultrasonic Waves.- II - Ceramics and Powder Metallurgy.- Origin of Flaws from Ceramic Processing (Invited).- Development of Nuclear Magnetic Resonance Imaging Techniques for Characterization Green-State Ceramic Materials.- Ultrasonic Evaluation of Spray-Dried Ceramic Powders During Compaction.- Ultrasonic Characterization of the Consolidation of Rapidly Solidified Powders: Application to Type 304 Stainless Steel.- Ultrasonic Scattering from Voids and Inclusions in Model Polycrystalline Ceramics.- Beam-Hardening Correction Methods for Polychromatic X-Ray CT Scanners Used to Characterize Structural Ceramics.- III - Metals.- Material Characterization for Process Control (Invited).- Important Metallurgical Parameters that must be Determined to Control the Properties of Steels During Processing (Invited).- Nondestructive Analysis of Structure and Stresses by Ultrasonic and Micromagnetic Methods (Invited).- A View of the Need and Technologies for In-process Materials Property Evaluation.- Determination of Subsurface Microstructure States by Micromagnetic ND-Techniques.- Detection of Coarse Grains by Nondestructive Magnetic Methods.- Ultrasonic Determination of Fracture Toughness.- Correlation Between Ultrasonic Attenuation and Fracture Toughness of Steels.- A Method to Calculate the Resistivity of Strip Cast 3000 Series AL Alloys Based on their Nominal Solute Content.- Ultrasonic Characterization of Candidate Nuclear Used Fuel Container Weld Materials.- Magnetoelastic Contribution to Ultrasonic Attenuation in Structural Steels.- Cyclic Plasticity of Pure AL Followed by Continuous Acoustic Emission Measurement.- Application of DTA to the Analysis of the Residual Austenite Transformation During Tempering.- The Dilatometric Method of Determining the Amount of Carbon Precipitated During Martensite Tempering.- Analysis of Elevated Temperature Properties of Heat Resistant Materials by Internal Friction Method.- A New Procedure for the Rapid Determination of Yield and Tensile Strength from Hardness Tests.- Mechanical Properties of Composite Materials Studied by Internal Friction.- IV - Layered Structures/Adhesive Bonds/Welding.- Characterization of Thin Film and Layered Structure by Pulsed Photothermal Radiometry.- Eddy Current Sizing of Case Depth in Bearing Components.- The Nondestructive Determination of Hardening Depths Using Ultrasonic Surface Waves.- The Characterization of Depth Profiles of Thin Films and Interfaces by Nuclear Scattering Techniques.- Nondestructive High Resolution Measurement of Polarization and Spatial Charge Distribution in Thin Dielectric Films.- Nondestructive Characterization of Thin Adhesive Bonds.- Interferometric Optical Fiber Measurements of Internal Strain in Adhesive Joints.- Automated Welding Process Sensing and Control.- Ultrasonic Characterization of Spot Welds.- V - Degradation/Aging.- An NDE System for the Detection of High-Temperature Rotors.- Nondestructive Degradation Evaluation of Ferritic Steels for High-Temperature